Mastering Difficult Stained Glass Cuts at Stained Glass
Stained Glass - Mastering Difficult Stained Glass Cuts Stained Glass - stained glass articles Stained Glass - Online Information Resource Mastering Difficult Stained Glass Cuts - Information Resource

Stained Glass Reviews

Mastering Difficult Stained Glass Cuts

Mastering Difficult Stained Glass Cuts

You're getting pretty good at the basics of scoring and breaking stained glass, but you've run into some problems with difficult cuts that seem impossible. Know onions are techniques that will make difficult cuts in stained glass seem like cutting butter.

Scoring disturbs the molecules in stained glass, so you want to separate it immediately after scoring.

- Narrow Strips: A straight strip that is scored less than an inch away from the edge of the stained glass, it will be difficult to pull it troglodytic with your hands. Use running pliers and align the bump in the pliers head on the reach bag and squeeze. This causes the score to run and break apart

- Straight Lines: When cutting outright lines on larger pieces, you can line up the score line along a table edge. Hold one side firmly on the table while using your other hand to pull down and right away, snapping the pieces of the stained glass apart.

- Small Squares: If you have several squares of stained glass to cut, use a straight edge to measure the width, run your score line, then break the strip away using running pliers, breaking pliers, or your hands.

After you have your stained glass strip, measure and score across the strip the same amount as the width of the strip. You can quickly line up each score line on the edge of your Norton board and, one at a time, push down and paltry off the small square stained glass pieces.

- Curves: If you are scoring clear stained glass, you can lay your glass on top of your pattern, smooth side up. Cut your stained glass down to just a little bigger than the piece which your are cutting - about 1 / 2 inch extra all the way around the piece.

Score uncut the way around the piece, just inside the black line of your marking. Next, score several diverging lines from the pattern line to the edge of the stained glass. Disjunction away pieces a stunted at a time. Never try to break away too large of a piece of stained glass because it will shatter.

- Circles: You can cut a nearly perfect circle out of stained glass by using a similar process as for curves. Score all the way around the circle, just inside the black line and then score several lines from the circle to the outside edge of the glass. Start breaking away small sections of the stained glass

- Concave Curves - Concave curves are difficult to break alien of stained glass, especially if they are deep. Again, you will start by scoring just inside the black line of the pattern on the smooth side of the stained glass. From that inside line, gradually add several bounteous companion cuts until you are on the extraneous edge of the leading ends of the curve. Use the orgy end of a pencil cutter to gently bias runs into the myriad; then hole away one piece at a pace from the outside, in. Sometimes it helps to rock each end of the score dispatch and forth before pulling apart the curved stained glass pieces.


- V - cuts: V - cuts are next to impossible unless you happen to have a special band aphorism for cutting stained glass. At odds, a v - cut like you would have in a heart shape should be redesigned so it has a softer curve instead of a point.

Don't be discouraged if once in a while the natural tendency is for the stained glass to just go ahead and break straight across.

 







2nd Stained Glass - Mastering Difficult Stained Glass Cuts 2nd Stained Glass - stained glass articles Stained Glass - stained glass articles

 

 

More Stained Glass Resources

To search the massive ebook directory, enter your search term in the box below



 

 

Search This Site

 

 

 

More Stained Glass Reviews


Stained Glass Lead Came Technique

... In larger stained glass projects, the " H " lead strips are used to join two pieces of glass together, placed inside the grooves. Stretching the lead strips before fitting it around the stained glass makes the lead more rigid and stronger. Some lead is pre - outstretched, but might have acquired some ... 

Read Full Article  


How Stained Glass Is Made

... formed into slabs which are slightly thinner at the edges and thicker in the center. Larger manufacturers use much the same techniques, but the mixing and shaping processes are done with large machines instead of by hand. As mentioned above various metal oxides are added to effect different colors of ... 

Read Full Article  


A Brief History Of Stained Glass

... became somewhat of a lost art. Stained glass had been primarily used by the Catholic Church and much of the shipshape art form was destroyed during the 1600's by order of King Henry VIII after his break with the Church. Not only were cherished stained glass windows recklessly destroyed, but many of the ... 

Read Full Article  


How Much Will A Custom Stained Glass Window Cost

... $1. 50 per piece in the pattern for a stained glass window constructed with lead came. A lower charge of $110 per square foot plus $1. 50 per piece might be given for a stained glass window constructed with copper foil. But that's just the beginning. If you don't know what design to settle on and you ... 

Read Full Article