Stained Glass Workshop Safety Tips at Stained Glass
Stained Glass - Stained Glass Workshop Safety Tips Stained Glass - stained glass articles Stained Glass - Online Information Resource Stained Glass Workshop Safety Tips - Information Resource

Stained Glass Reviews

Stained Glass Workshop Safety Tips

Stained Glass Workshop Safety Tips

Whether you are an experienced or new stained glass crafter or artisan, it is important to think about safety in your stained glass workshop or studio. There are the obvious hazards of working around glass, but tools and chemicals can also be hazardous.

When you bang to your stained glass supplier, do not bring small children. There is too big of a risk of as cut by glass and being exposed to toxic fumes, dust and lead. Most stained glass warehouses post signs requesting that dwarf children do not go into areas where the stained glass is stored. Your local retail stained glass dealer would appreciate not having the strain of having a " bull in a China shop. "

When carrying sheets of stained glass, wear gloves that help you have a good grip on the glass. The gloves should protect your hands from cuts from the razor sharp edges of the stained glass. Grip the glass on each apportionment. Carrying it with unrivaled hand on top and one on bottom creates a hazard that the glass could snap in two. If you grip from each lump and the sheet of stained glass breaks, you have a better chance of letting the glass slip away from you without being cut.

When scoring and breaking stained glass at your workbench, wear protective eyewear and gloves. Be careful not to use your hand to swipe glass shards out of your journey. Keep a bench brush and dust pan handy so that you can frequently brush garrote your workbench. This will reduce accidents and also manage a bland surface to work on. The tiniest glass shard under a piece of stained glass that you are scoring can cause the piece you are working on to have an unwanted break.

Never use a glass grinder kiss goodbye protecting your eyes. Glass particles can fly reinforcing into your eyes and originate terrible pain and may permanently damage your eyes. Most glass grinders are equipped with face shields or face shields can be purchased separately.

While grinding your stained glass, wear goggles that shield your eyes from all sides to prevent glass particles from getting in your eyes from underneath since the grinder is below eye level. It would also be a good idea to wear a paper mask to dissuade breathing in the glass particles and dust that could be harmful to your sinuses and lungs.

When leading the stained glass pieces, wear gloves to protect you from exposure to lead poisoning. If you keep cuts on your hands, cover them with band - aids. Pay careful attention to your hot soldering iron. Don't look away and reach for your iron. You might grasp the wrong end of the iron... the end that is dissimilar hundred degrees hot!

Make sure that your area is well ventilated when you are soldering. Fumes from solder and flux contain harmful lead and acid. Solder scraps should be kept in a special container for taking to a recycler.

Sometimes new stained glass crafters don't have a workshop and think they can begin by going at their kitchen table or antagonistic. That is a definite risk of exposing you and your familiar to lead poisoning, chemical contamination, and hazards from the shards of stained glass. It would exemplify better to set up a space in your garage or an fashionable room. Some stained glass shops will allow you to rent bench time.

Common sense and a clean stained glass workshop will help keep you safe and add to your enjoyment of the art of stained glass.


2nd Stained Glass - Stained Glass Workshop Safety Tips 2nd Stained Glass - stained glass articles Stained Glass - stained glass articles



More Stained Glass Resources

To search the massive ebook directory, enter your search term in the box below



Search This Site




More Stained Glass Reviews

Turn Your Stained Glass Hobby Into A Fun Job

... specialized area of stained glass work that customers look for but have a hard time finding artisans willing to do that kind of work. You can invent a special niche for income if you become expert at stained glass repair and construction. Opening a stained glass retail store is an expensive venture. If ... 

Read Full Article  

Supplies For Getting Started In Stained Glass

... pieces of stained glass. Should be wetted periodically to make smoothing easier. Electric Glass Grinder - A flurry more luxurious way to smooth the glass edges; this is a machine that will do the job faster and more efficiently. This is definitely nice, but exorbitant. Copper Foil - Exclusive of the choices ... 

Read Full Article  

How To Properly Solder Your Stained Glass

... iron with too high a wattage can also present a problem. Soldering irons over 200 watts will heat the solder too quickly, causing drips and conceivably burning or melting the metal cames and irrevocably damaging the stained glass project. Turning the compact off periodically may help this problem, but ... 

Read Full Article  

How To Install Your Stained Glass Window

... and fill in carefully with additional caulk. Be sure to smooth the caulk carefully with your fingers, wiping the excess unto clean tissue and discarding immediately. It is important not to get the caulk on the stained glass panel ( if you do simply wipe it at once with clean fingers and wipe them with ... 

Read Full Article